Datacom Systems D56 Průvodce řešením problémů stáhnout pdf (Strana 89)

–89–

Section 26. TROUBLESHOOTING GUIDE

S Y S T E M ( i n c l u d i n g W i r e l e s s )

SYMPTOM POSSIBLE CAUSE REMEDY

1. Transmitter signal not

received at 5881/5882.

1a. Transmitter or 5881/5882 not properly

powered.

1b. If Transmitter is 5827/5827BD, house code

not set in field ✱24, or transmitter not set

to same house code set in that field.

1c. Transmitter located too for from RF

receiver.

1d. Metal shielding between transmitter and

RF receiver.

1e. Transmitter malfunctioning.

1f. 5881/5882 malfunctioning.

1g. Transmitter No. (zone) not programmed.

1h. 5881/5882 address incorrect.

1i. Field ✱22 not set properly.

1a Check or change transmitter's battery.

Check AM100's AC power.

1b. Check code switches inside transmitter.

Must match with RF House Code

programmed in AM100.

1c. Move transmitter or RF receiver.

1d. Check for large metal obstructions, then

relocate transmitter if necessary.

1e. Verify by activating 5881/5882 with

another, similar transmitter. If O.K.

now, return defective transmitter.

1f. Verify by making sure other transmitter s

cannot activate 5881/5882. If defective,

replace and return original 5881./5882.

1g. Verify programming.

1h. Set DIP switch on 5881/5882 for address

“0."

1i. Set field ✱22 for “1."

2. Transmitter zone number

appears during Transmitter

Sniffer mode , but does not

clear.

2a. Transmitter zone type (ZT) is set to 00

(Not Used).

2b. Transmitter battery not installed.

2c. 5800 System transmitter not "enrolled" in

system.

2a. Set ZT to a valid active zone type in field

✱56.

2b. Install proper battery.

2c. "Enroll" unit in field ✱56 or ✱83.

3. Low Battery message on

keypad.

3a. "Bat" or “System Lo Bat” (no zone Nos.)

3b. "Bat" or “Lo Bat” + "00."

3c. "Bat" or “Lo Bat” + "nn."

3a. System battery is low or missing.

3b. Remote RF keypad battery is low.

3c. Transmitter for zone “nn” has a low

battery.

4. Periodic beep(s) from

keypad.

4a. System is in TEST mode.

4b. A transmitter low battery has occurred

and is displayed.

4c. A supervision CHECK has occurred.

4a. Enter "Code" + OFF to exit TEST mode.

4b. Enter "Code" + OFF and replace the

battery.

4c. Check the transmitter indicated.

Restore communication to the receiver to

cancel the condition.

5. With 5800 System, no

response to a transmitter in

normal operation, although

zone number clears during

Transmitter Sniffer mode.

Put control in TEST mode. If zone does not

respond, try operating the tamper switch or

another input to the transmitter.

5a. If another input causes the zone to be

displayed, the wrong input was "enrolled"

when programming.

5b. If no response at all from this transmitter,

this physical transmitter has not been

enrolled by the system. Transmitter

Sniffer display is being cleared by another

unit programmed for this zone.

5a. Delete input's serial number (not the

zone), and enroll the proper input (see

field

56).

5b. Determine which transmitter is

programmed for this zone and reprogram

as necessary.

6. Nuisance or phantom

alarm.

6a. Sensors not properly installed, wired, or

monitored.

6b. Universal transmitter (5817) programmed

wrong.

6a. Check installation to see if in accordance

with established procedure.

6b. Check programming switches on

transmitter.

7. Intrusion alarm for no

apparent reason.

7a. Protected door or window opened while

system armed.

7b. Improper user operation of exit/entry

delays.

7c. Magnets located too far from switches,

and/or doors and windows not properly

aligned.

7a. Check with all occupants of protected

home.

7b. Check setting of entry and exit delays .

7c. Check all openings for proper switch and

magnet orientation.

8. “CHECK” and zone number

2–8 is displayed.

8. Control has sensed a high resistance

condition on a loop in one of the hard-

wired zones (2–8).

8. Check the sensor or the loop wiring in

the affected zone. The system will not

arm until this condition is corrected (or

the affected zone is bypassed).

1 2 ... 84 85 86 87 88 89 90 91 92 93 94 ... 103 104

Komentáře k této Příručce

Žádné komentáře

Datacom Systems D56 Průvodce řešením problémů Strana 89

Komentáře k této Příručce

Související produkty a manuály pro Sítě Datacom Systems D56