Datacom Systems D56 Průvodce řešením problémů stáhnout pdf (Strana 60)

–60–

DOWNLOAD

INFORMATION

(

✱

94,

✱

95)

✱

94 DOWNLOAD PHONE NUMBER

| | | | | | | | | | | | | | | | | | |

Enter up to 20 digits as follows: 0–9, # +11 for “

✱

”, # + 12 for “#”, # + 13

for a pause. Do not fill unused spaces. End field by entering

✱

. To

clear entries from field, press

✱

95 RING DETECTION COUNT FOR DOWNLOADING 15

0-15 = number of rings before control picks up phone line

Refer to the chart below and program this field accordingly.

NOTE: If "15" is entered

in field

✱

95 to bypass an

answering machine, and

a 4285/4286 Phone

Module is included in the

system, you should note

the following:

When calling in from an

off-premises phone, the

user should make the

initial call, allow 1 to 3

rings only, then hang up.

The user should then call

again. The Phone

Module will now seize

the line, and 2 long tones

sound, followed by the

usual voice prompt for

the 2-digit access code.

If this procedure is not

followed, Phone Module

operation will not be

possible.

Phone Answering

Module Machine Downloading Field

✱

Yes No No Set for value other than “0” (1–14). This will enable

the control panel to answer the phone call. Other-

wise, it will not be possible to access the Phone

Module

Yes Yes No Set for a value higher than the number of rings for

which the answering machineis set. Example: if

machine is set for 4 rings, use a value of 5 or higher.

This is recommended so that the Phone Module can still be accessed if the answering

machine is turned off and does not answer the phone call.

Yes No Yes Set for value other than “0” (1–14).

Yes Yes Yes Enter 15. See note at left.

No No No Enter “0."

No Yes No Enter “0."

No No Yes Enter 1–14.

No Yes Yes Enter 15 to bypass answering machine.

OTHER PROGRAMMING

COMMANDS

✱

56 ZONE PROGRAMMING MODE

Interactive menu mode used for programming zone attributes and

report codes. Refer to the ZONE PROGRAMMING section for

procedure.

✱

80 OUTPUT DEVICES

Interactive menu mode applicable only if field ✱25 is programmed for

a 4229, 4204, or if Powerline Carrier devices are being used. Refer to

the OUTPUT DEVICES section for detailed procedure.

✱

81 ZONE LISTS FOR OUTPUT DEVICES

Interactive menu mode applicable only if ✱25 is programmed for a

4229, 4204, or if Powerline Carrier devices are being used. Refer to

the ZONE LIST section for detailed procedure.

✱

82 CUSTOM ALPHA EDITING

Interactive menu mode used to program zone descriptors. Refer to

the ALPHA DESCRIPTION PROGRAMMING section for procedure.

✱

83 SEQUENTIAL MODE

Interactive menu mode used to "enroll" RF transmitter serial

numbers. Refer to the SEQUENTIAL MODE section for detailed

procedure.

✱

96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. No. FOR

DOWNLOADING

Pressing ✱96 initializes the system for downloading.

✱

97 SET ALL PROGRAM FIELDS TO DEFAULT VALUES

Pressing ✱97 automatically loads all defaults and erases any

information previously programmed.

✱

98 EXITS PROGRAMMING MODE

Prevents re-entry by : Installer Code + 8 + 0 + 0

Allows re-entry only by Power-up then [✱] and [#].

✱

99 EXITS PROGRAMMING MODE

Allows re-entry to program mode by: Installer Code + 8 + 0 + 0 or

by Power-up then [✱] and [#].

1 2 ... 55 56 57 58 59 60 61 62 63 64 65 ... 103 104

Komentáře k této Příručce

Žádné komentáře

Datacom Systems D56 Průvodce řešením problémů Strana 60

Komentáře k této Příručce

Související produkty a manuály pro Sítě Datacom Systems D56