Datacom-systems J Class Uživatelský manuál Strana 48
- Strana / 273
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
2-2
This chapter describes how to configure your workstation to use a
printer that you have physically attached to either the parallel connec-
tor or the serial (RS-232C) connector on the rear of your workstation.
The instructions in this chapter assume you are using the HP-UX
version 9.05 or later operating system with the HP VUE version 3.0
interface.
NOTICES: Make sure you have installed the printer as
described in the manufacturer’s instructions
before following the instructions in this chapter.
Also ensure that the printer is powered on, con-
nected to your workstation, has paper loaded,
and is online.
Some procedures in this chapter require you to
log in as root. If you cannot log in as root, con-
tact your system administrator.
- Owner’s Guide 1
- Hewlett-Packard Co. 1995 2
- Documentation 7
- Conventions 7
- Questions 8
- Suggestions, or 8
- Problems 8
- Contents 9
- Setting Up Your Printer 10
- Using Your CD–ROM Drive 10
- Chapter 2 10
- Chapter 3 10
- Using Your DDS Tape Drive 11
- Chapter 4 11
- SCSI Connections 13
- The Boot Console Interface 13
- Appendix C 13
- Appendix D 13
- Glossary 14
- Chapter 1 19
- • Internal Storage Devices 22
- • Keyboards PS/2 Keyboard 23
- Front Panel 24
- Controls, LED 24
- System LCD 25
- System Power Switch 25
- • CD-ROM disc drive 26
- • DDS tape drive 26
- • Floppy diskette drive 26
- Removable Device 27
- Bays (2) 27
- Audio Connectors 30
- • Audio Inputs Line-in 31
- • Audio Outputs Line-out 31
- • Audio CODEC Crystal CS4215 31
- Keyboard Connectors 32
- HP Parallel I/O Connector 33
- 802.3 Network Connectors 33
- SCSI Connectors 34
- Power Cord Connector 34
- Monitors 35
- • PS/2 Keyboard 36
- • ITF Keyboard 36
- Keyboards 36
- Pointing Devices 39
- Operating 40
- Overview 40
- LANIC ID 41
- Terminal Control 42
- Networking 45
- Toolbox 50
- Up Arrow 50
- 13. Click on 52
- Exit SAM 54
- Printing a File 58
- Chapter 6 60
- Media Descrip 62
- CD-ROM Media 64
- Figure 6–4 67
- Figure 6–4. Disc Tray Closed 67
- The ioscan utility verifies 70
- Mounting and 74
- Unmounting a 74
- CD-ROM Disc 74
- Reading the Busy Light 80
- Troubleshooting 81
- Descriptions 84
- LEDs (light emitting 85
- Data Cassettes 88
- H/W Path Description Status 91
- Writing to a Data Cassette 95
- Further Command Information 98
- Ordering Information 99
- Chapter 5 100
- Using the Floppy 102
- Diskette 102
- Eject Button 103
- Operating the 104
- Floppy Drive 104
- Using Device Files 106
- Formatting a New Diskette 107
- For More Information 110
- • Using HP-UX (B2910–90001) 111
- Problems and 114
- Solutions 114
- The search command 121
- Failures 122
- Running System 126
- Verification 126
- 5. Press 127
- CSTM> exit 128
- Appendix A 129
- • Number 1 Posi-drive driver 130
- • Needlenose pliers 130
- Checking the 131
- SCSI IDs 131
- /usr/sbin/ioscan –f 132
- Opening the 134
- System Unit 134
- Closing the 136
- CD-ROM Drive 142
- 143
- DDS Tape Drive 144
- SCSI Terminators 145
- (must be removed) 145
- Top View of Floppy Disk Drive 150
- 14. Slide the drawer back in 152
- Adding a 155
- Hard Drive 155
- 156
- PCB Side of Drive 157
- Top Drive 157
- Bottom Drive 157
- Installing a Hard Disk Drive 158
- Configuring a Hard Drive 161
- 11. Click on 163
- Ejector Tab 165
- Memory SIMMs 166
- 167
- 167
- 11. Close the ejector tab 169
- Figure A–37 185
- Changing Your 188
- Monitor Type 188
- Appendix B 189
- VCCI Class 1 ITE 192
- Kingdom Only) 192
- CLASS 1 LASER PRODUCT 193
- LASER KLASSE 1 193
- Warnings and 194
- Cautions 194
- SCSI Bus 197
- Differences 197
- Priority 198
- SCSI–2 ID Number 198
- • fast-wide, SCSI-3 bus 201
- Determining 203
- Fast, Wide SCSI-3 Bus Length 206
- Assigning SCSI 208
- Device IDs 208
- Fast, Wide SCSI IDs 214
- Connecting to 215
- 216
- Boot terminated 225
- Booting Your 226
- Workstation 226
- ISL> hpux /SYSBCKUP 227
- Searching for 228
- Bootable Media 228
- Resetting Your 229
- Displaying and 229
- Setting Paths 229
- Setting the 231
- • Graphics slot 1 CRX48Z 232
- • Graphics slot 2 Empty 232
- Setting the Monitor Type 233
- Displaying the 236
- Configuration 236
- Sample Output 2 237
- Status of the 239
- EISA Slots 239
- Auto Boot and 240
- Auto Search 240
- Displaying 242
- Information 242
- Displaying PIM 242
- Workspace Manager 266
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce